No.

data sheet 1686


No tools were found, please check your input.

cutting rates

Main group Subgroup Hardness <= SFM [ft/min] VRC
Steel materialsCommon structural steels 500 N/mm2 607 75 - 76
1000 N/mm2 607 75 - 76
Free-cutting steels 850 N/mm2 607 75 - 76
1000 N/mm2 607 75 - 76
Unalloyed heat-treatable steels 700 N/mm2 607 75 - 76
850 N/mm2 607 75 - 76
1000 N/mm2 607 75 - 76
Alloyed heat-treatable steels 1000 N/mm2 607 75 - 76
1400 N/mm2 607 75 - 76
Unalloyed case hardened steels 850 N/mm2 607 75 - 76
Alloyed case hardened steels 1000 N/mm2 607 75 - 76
1400 N/mm2 607 75 - 76
Nitriding steels 1000 N/mm2 607 75 - 76
1400 N/mm2 607 75 - 76
Tool steels 850 N/mm2 607 75 - 76
1400 N/mm2 607 75 - 76
High speed steels 1400 N/mm2 295 75 - 76
Spring steels 350 HB 148 73 - 74
Stainless steels, sulphured 900 N/mm2 295 74 - 75
Stainless steels,austenitic 1100 N/mm2 197 74 - 75
Stainless steels,martensitic 1200 N/mm2 295 74 - 75
Hardened steels 48 HRC 164 73 - 74
65 HRC 148 73 - 74
Cast materialsCast iron 240 HB 328 75 - 76
350 HB 328 75 - 76
Spheroidal graphite iron and malleable cast iron 240 HB 607 75 - 76
350 HB 295 75 - 76
Chilled cast iron 350 HB 131 74 - 75
Copper, bronze, brassBrass, short-chipping 600 N/mm2 574 75 - 76
Bronze, short-chipping 600 N/mm2 574 75 - 76
850 N/mm2 574 75 - 76
Magnesium-alloysMagnesium alloys 450 N/mm2 394 75 - 76
Titanium and Titanium alloysTi and Ti-alloys 850 N/mm2 197 74 - 75
1400 N/mm2 197 74 - 75
PlasticsDuroplastics 150 N/mm2 459 75 - 76
Thermoplastics 100 N/mm2 459 75 - 76
Materials for special applicationsSpecial alloys 1600 N/mm2 164 74 - 75

 


Feed

fu [in]VRC
d1[in] <= 73747576
0.1240.00490.01180.01970.0315
0.15750.00630.01180.01970.0394
0.19690.00630.01570.02360.0394
0.2480.00790.01570.02760.0472
0.3150.00980.02360.03940.0709
0.39370.01240.02360.04720.0709
0.49210.01240.03150.04720.0787
0.62990.01570.03150.05510.0866
0.78740.01970.03150.05510.0866

Master data

DescriptionCarbide high performance reamers
StandardGuhring standard
Surface finish
Cutting directionright hand
Tool materialCarbide
on shankDIN 6535-HA
Coolantaxial
Hole typethrough hole
TypeHR 500 D
Tolerance zoneH7
Discount group166


Dimensions

d1 [mm]l1 [mm]No. of flutesShank Ø d2 [mm]Flute length l3 [mm]Cutting edge length l4 [mm]Protruding length l2 [mm]d2 [mm]incision length l6 [mm]
3.000684440124030.7
3.50068444012403.50.7
4.000684421124041
4.50076462112404.51
5.000764621124051
5.50076462112405.51
6.000764621124061
6.500101682516656.51
7.0001016825166571.4
7.500101682516657.51.4
8.0001016825166581.4
8.5001016103319618.51.4
9.00010161033196191.4
9.5001016103319619.51.4
10.000101610331961101.4
10.50013061234198510.51.4
11.000130612341985111.8
11.50013061234198511.51.8
12.000130612341985121.8
13.000130614392285131.8
14.000130614392285141.8
15.0001506164022102151.8
16.0001506164022102161.8
17.0001506184425102171.8
18.0001506184425102181.8
19.0001506204525100191.8
20.0001506204525100201.8

Please wait a moment
Session expires ...